Electro-Magnetic Radiation (EMR) Interaction with Earth Surface Features

In this article discuss the interaction of Electro-Magnetic Radiation (EMR) with earth surface features. After passing through atmosphere, the EMR reached to earth and as already discussed EMR which have least or almost no interaction with atmosphere is used by remote sensing sensors. 

This part of spectrum is called atmospheric windows, which have zero or no interaction with atmosphere. 

When EMR reached and interact with earth’s feature, three things take place with incident energy.

When EMR is incident on any earth feature then part of it, as shown in figure
  • Reflected
  • Absorbed
  • Transmitted
Figure showing Interaction of sun energy (EMR) with Earth Surface Features

Estimated radiation states that sum of these energies (reflected, absorbed and transmitted) is equal to incidental energy on earth’s feature.

How much amount will be reflected or absorbed or transmitted depends upon material to material as well as many other conditions. 

These quantities are sometimes expressed in non-dimensional way as

Transmittance– 

This is defined as radiation which penetrates into certain surface materials such as water with some fraction (up to 100%) of the incident radiation.
It depends on material property, if the material is more transparent and thin than there will be more transmittance.

Absorptance– 

It take place when incident energy is absorbed by molecular reactions, Sometimes portion of this incident energy is then re-radiated and some of it remains there and heats the objected target.

Reflectance– 

It is also defined as re-radiation from earth’s features. Most of the radiations are reflected and scattered from the target at various angles. 
It is depend upon the property of feature such as surface roughness and also the incidence angle of the EMR. 

This reflectance is very important in this process as it is received and recorded by satellite sensor.

It helps to differentiate materials based on reflectance received for different elements on earth surface. It may possible that same material/object have different reflectance value with change in wavelength. 

Therefore, it can be concluded that features with same reflectance in one wavelength, may have different reflectance values in some other wavelength and it helps to distinguish object with change in wavelength.

As it is understood that reflectance from earth’s feature is key parameter in remote sensing process, because it is sensed by sensor. Surface property of object will become very important in reflectance process.

Various types of surface reflect EMR in different ways some are Perfect Specular Reflector, Near-Perfect Specular Reflector, Perfect Diffuse Reflector and Near-Perfect Diffuse Reflector.

Earth Surface Features Properties

There are basically three type of surface or natural surface cover on the earth
  • Vegetation
  • Soil
  • Water
So reflectance will take place based on the properties of these natural land cover.

Vegetation-

There is a drop in reflectance value in the visible spectrum due to chlorophyll, as it is absorbs strongly in and around 0.45 mm and 0.67 mm wavelength. This is also called as chlorophyll absorption bands. 

If any plant is not healthy in that case the absorption would be less and reflectance will be more.

In near IR, reflectance increases dramatically and reached nearly about to 40-50% and most of the remaining part is transmitted.

Water –

Most of the incident energy will be absorbed by water and there will be less or no reflectance received by sensor. Maximum reflectance reaches to hardly 10% in case of water and also only in visible part of spectrum.

Soil- 

In case of soil, reflectance will be more as compared to others. But reflectance depends upon various factor or properties such as Moisture content as it decreases reflectance.

Soil texture coarse texture soil will have lower moisture content & higher reflectance Surface roughness
Presence of organic matter content in soil as it also decreases reflectance

The ultimate reflectance of object is received by sensor and converts this reflectance to form an image.
Comments 5
Leave a Reply

Your email address will not be published. Required fields are marked *

Prev
Electro-Magnetic Radiation Interaction in the Atmosphere

Electro-Magnetic Radiation Interaction in the Atmosphere

Remote sensing process depends on source of energy, it can be natural in the

Next
REFLECTANCE OF EARTH SURFACE FEATURE AND SPECTRAL SIGNATURE OF SATELLITE IMAGE

REFLECTANCE OF EARTH SURFACE FEATURE AND SPECTRAL SIGNATURE OF SATELLITE IMAGE

This article is prepared to understand the role of reflectance and spectral